WIFI Range Extender VICTONY WA305 for 2.4G 300Mbps WiFi Signal Booster with 2 External Antennas
It’s meant to enhance your existing wireless network’s Wi-Fi range and signal strength with two external antennas for improved performance in extending wifi signal to dead spots.
It has a high compatibility with 802.11 b/g/n wireless devices, network cards, and routers.
It has exquisite craftsmanship and cutting-edge technology to meet your different Internet browsing demands at a speed of 300Mbps.
WPS one key installation, set up via online interface wirelessly or wired via a device, such as a phone, pad, computer, and so on.
Two ethernet ports (10/100M) to connect wired devices, such as a computer, smart TV, and so on; smart LED light to assist you choose an optimal spot to instal the extender; and two ethernet ports (10/100M) to connect wired devices, such as a computer, smart TV, and so on.
The VICTONY WA305 wifi extender’s main purpose is to expand an existing wifi signal to a far-reaching location where the signal is weak. Two external antennas to reach dead spot with a more steady, stronger signal. Multiple wireless enabled devices can be connected at the same time with a 300Mbps transfer rate. Easy setup: 2 minutes through wps button or website configuration 802.11 b/g/n to create a broad, no-drop wireless network for multiple users. Wireless Standard: IEEE 802.11 b/g/n Wi-Fi Band: 2.402-2.4835GHz Max Throughput: 300Mbps Transmission:2.4 GHZ band System Requirement: 100 240-volt socket WLAN access point/client compliant with IEEE 802.11n, g, and b standards. At the very least, the WLAN client must support the WPA encryption standard. (DHCP) Forwarding of IPv4-based protocols/Address Resolution Protocol between the WLAN access point and the WLAN client with automated IP address assignment.
Setup for the Victony WA305 Extender
The Victony WA305 Extender Setup is a dual-band wireless extender configuration. That will improve your wifi connection or wifi network, giving you the best-uninterrupted gaming, movies, and web series experience possible. With the Victony WIFI Extender Setup’s four external antennae, you can expect unrivalled wifi range across your house or business. Your new extension configuration is incredibly simple to connect. It’s a plug-and-play gadget that takes 15 seconds to connect to any router. Victony WIFI Range Extender configuration features three modes: router, repeater, and access point, which you may use based on your needs. However, when you change the mode, don’t forget to reset or reconfigure your Ap.setup.
VIA WEB BROWSER SETUP FOR VICTONY WI-FI EXTENSION
First and foremost, you must place your Victory wifi extender and router in the same room.
Ensure that the signal from your router reaches the extender at least 50% of the time.
Turn your router and extension on now.
After a few seconds, check to see if the LED light is stable or solid green.
Open your wifi settings on your laptop, PC, or smartphone and connect to the victony wa305 extender configuration.
The first time they connect to your device, there is no need to enter a password because they connect immediately.
After connecting, they stated that there was no internet available and then loaded any online browser.
The New Extender Setup or 192.168.10.1 login window will display if you put it in the address bar at the top.
Your username and password should both be “admin.”
Select the extender to which you wish to connect your router and enter your new extender setup password.
After you’ve done setting up the device, reset it for 15-20 seconds to turn it back on.
Connect your device to the Victory wifi range extender configuration, which appears in your wifi list as “SSID EXt.”
WPS SETUP FOR THE VICTONY EXTENDER
Using the WPS button to configure your Ap.Setup. Set up your AP extender by following the instructions below.
Using an ethernet wire, connect your extender to your router.
Wait until the LED light stabilises.
Then, for 5 seconds, push the WPS button.
Both devices’ lights will flash, and when they cease blinking after 15-20 seconds, it means the setup was successful.
With range extender setup, you now disconnect your new extender setup and place it wherever you want.
The new extender will appear in your wifi list as “SSID EXT,” with the same password as your router.
WPS button configuration for Victony WA305 WiFi Extender
The following are the procedures to set up the Victony WA305 Extender WPS button:
On your host router, hold down the WPS button for 2 seconds.
Press WPS for around 2 seconds on the extender in the same way.
The signal LED will turn solid blue after a short period of time, indicating that the WPS button connection was successful.
And, on top of that, you may experience seamless, strong Internet surfing from everywhere in your house, removing all dead zones.
Update the firmware on your Victony WA305 wifi extender
Following the simple instructions below, you may upgrade the Victony WA305 extender firmware:
Download the latest firmware file from the company’s official website.
Enter your extender’s login and password on the ap.setup webpage.
Go to System Tools in the menu bar and click on it.
Upgrade Firmware by clicking the button.
Select Upgrade and navigate to the firmware file you just downloaded.
Restart the extender when the upgrade is complete. Your extension’s firmware has been successfully upgraded.